Gasket maker,supra grey
- OEM specified.
- outstanding oil resistance and joint movement tolerance.
- eight times more flexible than cork/composite gaskets,three times moro oil resistant than conventional silicones
- temperature range -70° to +260° intermittent,
- resists auto and shop fluids and vibration
- automobile suggested application :valve covers,oil pans,transmission pans,intake manifold end seals,timing covers ,water pumps,thermostat housings
- marine suggested application :cover housing gasket,differential,assembly to rear axle housing, power dividers, axle shaft flanges
Customers who bought this product also bought:
A tread gauge also known as a screw pitch gauge or pitch gauge,is used to measure the pitch or lead of a screw thread.The uppermost gauge in the image is an ISO metric and whitworth screws pitch gauge. ISO METRIC 0,4 -0,5-0.6-0,7-0,75-0.8-0.9-1-1.25-1.5-1.75-2-2.5-3.0-3.5-4.0-5.0-5.5-6.5-7 WHITWORTH...
φρέζες μετάλλου 90°
Metal countersink 83 HHS-CO ,3 flute 90° high speed ground deburring countersinks with three sharp 90° degree cutting edges for rabid swarf clearance hss ground with three sharp 90° degree cutting edges for rapid swarf clearance suitable for use on sheat metal ,cast iron ,aluminium,non-ferrous metals and plastic
Complete thread repair kit - Including the required drill V-Coil tap and drill made from High Speed Steel V-Coil wire thread inserts manufactured from aerospace specification stainless steel Due to the narrow and accurate tolerances, the newly repaired thread is usually stronger than the original thread
Φλαντζωτό παξιμάδι DIN6923
Hexagon nut with flange DIN6923 zing plated m 4 Χ 0.75 The flange enables built up forces unter the nut to be spread over a larger albe,conseguently resulting in lower surf plessure large (overized) holes and or tooling holes can be covered by the flange washes are not necessary
Set of 5 screw extractors for removing sheared off screws and bolts m3 - m18.Simple drill a pilot hole in the broken screw in the left hand threaded extractor until bolt turns screw extractor 2.7 mm for screw Μ 3 - Μ 6 ή 1/8" - 1/4" screw extractor 3.4 mm for screw Μ 6 - Μ 8 ή 1/4" - 5/16" screw extractor 4 mm for screw Μ 8 - Μ 11 ή 5/16"-7/16"...
Cold weld,steel reinforced,bonds to alouminioum,brass,bronze,copper,iron,stainless steel and steel.A two parts, high strength,cold welding epoxy that can be drilled,threaded,machined,filed or painted,once fully cured.Has a test -proven shear strength than 3000 psi after 16 hours.Resistant To shop fluids,including diesel...
φρέζες μετάλλου 90°
Metal countersink 10,4 HHS-CO ,3 flute 90° high speed ground deburring countersinks with three sharp 90° degree cutting edges for rabid swarf clearance hss ground with three sharp 90° degree cutting edges for rapid swarf clearance suitable for use on sheat metal ,cast iron ,aluminium,non-ferrous metals and plastic
special tools for auto and moto.
4 other products in the same category:
Motor sealant creates exceptionally elastic and resistant seals.It fils all gaps and surface irregularities.It passes even the most stringent tests performedon seals.It self-vulcanizes at room temperature and resists thermal changes from -70 to 260 (with peaks of up to 350 .It resists water,gas,petrol,mineral,spirits,oil and anti-freeze products.Resistant...